Smart Series
Managed fiber networking you run from your phone.
Every unit in the Smart Series is remotely managed. Configure it, read live optical power and port health on the built-in screen or a mobile app, and get an alert the moment a link degrades — with no laptop, no optical meter, and no return trip to site. Fewer truck-rolls, faster commissioning, longer uptime.
Smart Managed Media Converters
Extend Ethernet over fiber and see the whole link. Standard 10/100/1000M, 2.5G and 10G converters that turn a copper port into a fiber link — and let the installer verify optical health from the ground, not the ladder.
Copper Ethernet dies past ~100 metres, and an unmanaged converter is a black box — when a fiber link is weak, the installer has no way to know without carrying an optical power meter to every end. The Smart converter puts live optical Tx/Rx power, distance and port status on the unit and in the app, so a link is verified — or a fault is located — in seconds, from the ground.
Features
- Mobile app + web management — configure and monitor without a laptop or test meter.
- One-click front-panel screen — system current, voltage, temperature; optical Tx/Rx power; Ethernet and fiber port rates.
- Full SFP DDM diagnostics — optical power, wavelength, transmission distance, data rate and module temperature.
- User-defined optical-power thresholds and scheduled reboot.
- Real-time multi-level alerts on link and threshold events.
- Auto-negotiation, auto MDI/MDI-X; IEEE 802.3x flow control and back-pressure.
- Standards — IEEE 802.3 / 3u / 3ab / 3z, plus 802.3bz / 3an / 3ae on 2.5G–10G models.
- Lightweight interface designed for on-site use by non-specialists.
Models
| Antek Code | Configuration | Speed |
|---|---|---|
| AL-11001 | 1× RJ45 · 1× SFP | 10/100/1000M |
| AL-11003 | 1× RJ45 · 1× SFP | to 2.5G |
| AL-11005 | 1× RJ45 · 1× SFP/SFP+ | to 10G |
| AL-11007 | 2× RJ45 · 1× SFP | 10/100/1000M |
| AL-11009 | 1× RJ45 · 2× SFP | 10/100/1000M |
Where used: fiber backbones for CCTV and data networks, building-to-building links, campus and industrial sites, rail, road and utility monitoring.
PoE Media Converters
One box that extends the link over fiber and powers the device at the far end — an IP camera, a wireless AP, an access controller — over the same cable. PoE+ to PoE++ 90 W.
A camera on a pole 400 metres out has no mains power and no switch nearby. Running power to it means an electrician and a permit; a switch at each end is overkill. The PoE converter carries the link over fiber and delivers up to 90 W down the copper to the device — one cable, no local power, no second trade on site.
Features
- Integrated PoE PSE — IEEE 802.3af / at / bt, up to 90–95 W PoE++ with voltage booster.
- Powers PTZ cameras, heaters and multi-radio APs with full headroom.
- All the managed diagnostics of the standard range — app/web, front screen, DDM, thresholds, alerts.
- Per-port power visibility and fault alerting.
- Auto-negotiation, auto MDI/MDI-X; store-and-forward.
Models
| Antek Code | Configuration | PoE Budget |
|---|---|---|
| AL-11002 | 1× RJ45 · 1× SFP | 95W PoE++ |
| AL-11004 | 1× RJ45 · 1× SFP (2.5G) | 95W PoE++ |
| AL-11006 | 1× RJ45 · 1× SFP+ (10G) | 95W PoE++ |
| AL-11008 | 2× RJ45 · 1× SFP | 95W PoE++ |
Where used: perimeter and gate cameras, car-park and street CCTV, remote wireless APs — any powered device at the far end of a fiber run.
OEO Converters & 3R Repeaters
Fiber-to-fiber regeneration for backbone and long-haul links — wavelength conversion, rate adaptation, and 3R signal regeneration to rebuild a clean optical signal over distance. 10G, 25G and 100G/40G.
Over long metro and backbone spans an optical signal attenuates and its timing smears until the link errors. A plain patch can’t fix that. The 3R repeater actively re-amplifies, re-shapes and re-times the signal — and converts wavelength (1310/1550nm, CWDM/DWDM) — so one span reaches far beyond a single optic’s budget, with loopback testing built in for fast fault isolation.
Features
- 3R regeneration — re-amplify, re-shape, re-time for clean long-haul signals.
- Wavelength conversion — 1310 / 1550 nm, CWDM and DWDM.
- Backbone protocols — SDH/SONET STM-64/OC-192, Fibre Channel, 10G/25G/100G Ethernet.
- Built-in loopback test and Type-C management access.
- App/web management with front-panel DDM display; multi-level alerts.
- Chassis-mountable (100G/40G model) for rack density.
Models
| Antek Code | Class | Rate |
|---|---|---|
| AL-21001 | 10G OEO | 125M – 10G |
| AL-21002 | 10G OEO · 3R | 1.25 – 12.5G |
| AL-21003 | 25G OEO · 3R | 10.3 – 25.78G |
| AL-21004 | 100G/40G OEO · 3R | 40G / 100G |
Where used: SAN/LAN/MAN backbones, data centres, telecom rooms, R&D labs, DWDM metro links.
Industrial Media Converters
The managed converter, hardened for the cabinet: wide 9–54 V DC input, DIN-rail mount and wide-temperature operation — built for Gulf roadside, rooftop and factory-floor deployment.
A commercial converter rated to ~45 °C reboots every afternoon inside a Gulf street cabinet that passes 60 °C in summer — and every reboot is a truck-roll. The industrial range is rated to +75 °C, fanless, DIN-rail mounted, and runs off a wide 9–54 V DC supply (site power, battery or solar). It stays up through the summer and reports its own health remotely.
Features
- Wide-temperature operation to −40 to +75 °C, fanless — no filter to clog, no fan to fail.
- Wide 9–54 V DC input — runs off site power, battery or solar backup.
- DIN-rail mount for standard field cabinets.
- Full managed diagnostics — app/web, DDM, thresholds, alerts — for unattended remote sites.
- PoE variants to 90 W (with voltage booster) for powered field devices.
Models
| Antek Code | Configuration | PoE |
|---|---|---|
| AL-31001 | 1× RJ45 · 1× SFP | — |
| AL-31002 | 1× RJ45 · 1× SFP | 30W |
| AL-31003 | 1× RJ45 · 1× SFP | 60W |
| AL-31004 | 1× RJ45 · 1× SFP | 90W |
| AL-31005 | 2× RJ45 · 1× SFP | opt. |
Where used: roadside & perimeter CCTV cabinets, traffic/ANPR, factories, oil & gas, utilities, pump and solar sites. Full 30/60/90 W range on the line card.
Industrial PoE Switches
The whole cabinet in one hardened box: aggregate and power several cameras on copper, carry the link back over fiber, and manage every port remotely. 4- and 8-port, with 1–2 SFP uplinks.
A perimeter position has four cameras, no mains, and one fiber back to the control room. Cabling four separate converters plus a power supply is bulky and fragile. One industrial PoE switch powers all four cameras, aggregates them, and sends a single managed fiber uplink home — a hardened cabinet-in-a-box that reports every port’s status remotely.
Features
- 4- or 8-port PoE on copper, with 1–2 SFP fiber uplinks.
- PoE+ to PoE++ — 30 / 60 / 90 W per port options.
- Wide-temperature, fanless, DIN-rail; 9–54 V DC input.
- Managed — per-port monitoring, fiber-link DDM, threshold alerts, remote reboot.
- Store-and-forward switching; auto-negotiation, auto MDI/MDI-X.
Models
| Antek Code | Ports | Uplink |
|---|---|---|
| AL-31009 | 4× RJ45 | 1× SFP |
| AL-31010 | 4× RJ45 · PoE+ | 1× SFP |
| AL-31013 | 4× RJ45 | 2× SFP |
| AL-31017 | 8× RJ45 | 2× SFP |
| AL-31018 | 8× RJ45 · PoE+ | 2× SFP |
Where used: outdoor & perimeter CCTV, city surveillance, traffic systems, factories, warehouses, utility sites. 60/90 W variants on the line card.
Industrial 10G Media Converters
10-Gigabit over fiber in a hardened, DIN-rail form — multi-rate copper to SFP+, for high-bandwidth aggregation and industrial backbones at the edge.
High-camera-count sites and edge-compute nodes now push past gigabit, but the link still has to survive an outdoor cabinet. These converters bring true 10G over SFP+ fiber in the same hardened, DIN-rail, wide-DC form as the rest of the industrial range — with PoE++ options to power high-draw edge devices.
Features
- 10-Gigabit multi-rate copper (1G/2.5G/5G/10G) to 1.25G–10G SFP+ fiber.
- Hardened & DIN-rail; 9–54 V DC input.
- PoE++ options to 90 W for high-draw 10G edge devices.
- Full managed diagnostics — app/web, DDM, thresholds, alerts.
Models
| Antek Code | Configuration | PoE |
|---|---|---|
| AL-41001 | 1× RJ45 (10G) · 1× SFP+ | — |
| AL-41002 | 1× RJ45 (10G) · 1× SFP+ | 30W |
| AL-41003 | 1× RJ45 (10G) · 1× SFP+ | 60W |
| AL-41004 | 1× RJ45 (10G) · 1× SFP+ | 90W |
Where used: high-bandwidth CCTV aggregation, industrial backbones, edge compute, video walls.
Common Specifications
Shared across the Smart Series managed range. Exact figures vary by model — confirm against the datasheet for the specific Antek code.
- Management
- Mobile app + web GUI; front-panel screen; SNMP-style alerts
- Diagnostics
- Full SFP DDM — optical power, wavelength, distance, rate, temperature
- Ethernet Standards
- IEEE 802.3 / 3u / 3ab / 3z; 802.3bz / 3an / 3ae on 2.5–10G
- Flow Control
- IEEE 802.3x (full duplex) · back-pressure (half duplex)
- Fiber Reach
- Multimode 550 m / 2 km · Single-mode to 200 km (SFP-dependent)
- PoE (PoE models)
- IEEE 802.3af / at / bt — 30 / 60 / 90 W with voltage booster
- Power — Standard
- External AC-to-DC adapter, wide DC input
- Power — Industrial
- 9–54 V DC, DIN-rail; wide-temperature to +75 °C
- Compliance
- CE · FCC · RoHS compliant (documents on request)
- Warranty
- 3 years
Specifications are indicative and derived from current product datasheets; confirm exact figures per Antek code before quotation.